They're necessary. Ground loss—the quantity of sunlight falling between heliostats—is atrocious in current generation CSP's. Obvious in a satellite view is the fact that far more sunlight is reaching the ground than the mirrors. Land requirements are being tripled! The Second Law of Thermodynamics decrees that a heliostat without ground loss must act like a telescope, i.e., it must increase the divergence of the reflected beam while maintaining collimation (parallel rays map to parallel rays.)
Telescopic heliostats must have two mirrors. No fewer than two lenses (objective and eyepiece) compose a telescope.
Optimum power is about 6X. Magnifying the sun's disk, which is 0.5° in diameter, six times makes an intensified, but still collimated beam (or highbeam) that can be aimed at an elevation angle as small as its own diameter, 3.0°. That condition minimizes the height of the central, beam-down optics or lamp.
Central, beam-down optics are necessary. At 3.0° divergence, the highbeams are simply too spread to form a high quality focus without another optical stage.
The lamp (central beam-down optics)—shaped something like an overturned apple—will be only 60% as tall as a power tower on the same field. Larger heliostat fields are thus made practical.
The objective needs to move, the eyepiece doesn't. The objective (primary) mirror can redirect sunlight vertically to a fixed focus: the much smaller eyepiece (secondary) mirror gets to sit right there.
The objective needs to have its optical profile continuously fine-tuned to the sun's changing zenith distance. To first order, the adaptation needed is simply a thin-shell bending of the mirror.
Telescopic heliostats move in concert. The only real difference between two telescopic heliostats in a field is the azimuth aiming of their eyepieces. All the objectives could be mechanically ganged.
At at 0.70 mirror/land ratio, telescopic heliostats can be sited with negligible blocking. Surprisingly, the presence of the eyepieces adds no complication at all to heliostat siting when a phyllotaxis-based algorithm is used. The packing density achieved is more than three times that of a conventional heliostat field.
These improvements in field size and field packing make it practical to design a replicable 1 GW, 75% capacity-factor, standard solar plant covering one quarter-township (9 square miles) in the southwest U.S. The central lamp, about 190 m high, would be only 20% taller than current-generation power towers. Goodbye coal!
Showing posts with label blocking. Show all posts
Showing posts with label blocking. Show all posts
Wednesday, January 29, 2014
Friday, November 1, 2013
Low-aiming, target points, and optimization
Aiming slightly low in the outer portion of the heliostat field, and slightly high in the inner portion of the field, offers the advantage of making the focal zone more compact. This variable aiming can be idealized as aiming all the heliostats that lie on the same azimuth from the origin toward a single target point behind the focal zone. When heliostats are targeted in this way, the locus of the geometric constraint—the ideal shape of the beam-down optics—is no longer a family of confocal parabolas, instead it is a family of ellipses having as their foci the target point and the oculus center.
Whatever happens near the inner radius of the field is of minor importance due to the relatively small number of heliostats involved. On the other hand, what happens with heliostats near the outer radius of the field is important because there are the most numerous rows of heliostats.
Low-aiming of heliostats at the periphery can be carried too far. With constant aiming, the lowest ray in the beam from a secondary rises at only beta/2 (1:36 with 6x telescopic heliostats.) Lowering aim by a mere beta/2 would send the lowest rays traveling horizontally—guaranteeing that they would hit the back of another secondary. In fact, any lowering of the aiming angle will entail either some blocking by other secondaries (should we keep the primaries close-packed) or a decrease in land utilization (if we space the primaries out.) An optimized system will always have a bit of every possible kind of loss: all the possible losses come out to play in the big trade-off game. For the purpose of a simple baseline design we can be arbitrary: we will insist on zero blocking loss, but we will permit the land utilization in the outermost row to fall to 2/3.
![]() |
| The circles are the primary mirrors viewed from above; the ellipses are the shadows cast on a horizontal plane by the secondaries when illuminated from the direction of the lowest ray in there beam. |
At the last row we allow 2/3 land utilization, meaning that low-aiming is permitted to increase the surface area of the ellipses by 50%: their aspect ratio can increase from 36:1 to 54:1. So, at the last row, the lowest ray can have a run-over-rise of 54:1, which is an elevation angle of 1.1°. Recalling that the beam spread is 3°, the middle ray will have an elevation angle of 2.6°, or a run-over-rise of 22:1; the top ray will have an elevation angle of 4.1°, or a run-over-rise of 14 (putting that in a short hand, the outer heliostat operates at: 14-22-54, in run-over-rise numbers, which are also the reciprocals of the elevation angles measured in radians.) By comparison, a heliostat at its design condition operates at 12.4-18.5-36.
The unique row of heliostats that operates with both design condition aiming and chock-a-block packing should be located somewhere near the median radius of the field (outer radius / sqrt 2.) The top image diagrams such a system. The target point turns out to be little bit higher than the beam-down optics, and about one field radius behind the center of the field.
The run-over-rise number for the top ray of the outermost heliostats—in this example, 14—is also the ratio of the field radius to the tower height (or height at the top of the beam-down optics.) Telescopic heliostats give twice the value for conventional heliostat fields, but with much better land utilization.
Thursday, October 24, 2013
In what sense are telescopic heliostats telescopic?
| A pair of binoculars focussed at infinity and aimed at the sun emit intense beams from the eyepieces. |
Definition: A telescopic heliostat is a heliostat in which the emergent rays are increased in concentration and divergence.A telescopic heliostat is not telescopic in the sense that it can throw a beam of sunlight farther. If that were the only consideration, a plane-mirror heliostat would be the best choice. A telescopic heliostat concentrates sunlight while keeping the emergent rays as parallel as possible—which is precisely the action of a telescope focussed at infinity. An inevitable consequence of the concentration, is that the emerging light rays are more divergent than a natural sunbeam, so beam spread from a telescopic heliostat is greater than from a conventional heliostat.
![]() |
| An optical cross-section of a telescopic heliostat shows it to be an afocal, off-axis, Cassegrain telescope. Both mirrors are parabolic. |
![]() |
| The object of a heliostat is to hit a target of low angular elevation. (Note how much sunlight falls to the ground in the process.) Image quoted from NRG Energy. |
If hitting a distant target were the object of a heliostat we would stick with plane mirrors; but the object of a heliostat is to hit a low target. There are practical limits to the height that a boiler or beam-down optics can be elevated above the ground, so the goal of a heliostat is to redirect sunlight to a target of low angular elevation.
When 100% of the sunlight incident on a horizontal surface at angle of incidence θi emerges redirected at an angle of reflection of θr, the sunlight has been concentrated by a factor of cosθi / cosθr . The Second Law of Thermodynamics forbids this concentration without a compensating increase in divergence. Since plane mirrors cannot accomplish the required increase in divergence, they cannot accomplish the desired efficient redirection of light.
Consider, for example, the Ivanpah Solar Project in California. According to the 2010 environmental impact statement for this project, each power tower is 140 m tall measured to the top of the boiler. Ivanpah units 1 and 2 each have 55,000 heliostats, with each heliostat carrying 14 m2 of mirror. Let's say 1 m2 of mirror typically shades 1.5 m2 of ground. Each unit occupies about 915 acres (3.7 million m2) of land, but only 55,000 x 14 x 1.5 = 1.2 million m2 are typically shaded, a land utilization of only a third. To achieve full utilization we would need to squeeze three times as many heliostats into the view above—but they would only block each others' view!
Mutual blocking is worst at the farthest edge of a heliostat field, so land utilization there is really poor. Ultimately it makes more sense to build another tower than to extend a low-utilization field to greater radius. Approximating an Ivanpah unit as a circle, it has a radius of 1085 m. From the farthest edge of the field the top of the boiler has an angular elevation of arctan(140/1085) = 7.4°.
Subscribe to:
Posts (Atom)



